KAS-Keyless Access Security

            Neo Lock - Installation

            Installation 

             Preface

            • Electronic locks are sensitive and advanced products with fragile microchips and hardware. Please be aware that the position and type of environment the lock is installed in can affect its lifespan.

            • To install the lock, we recommend professional carpenters or builders. Incorrect installation of the lock can lead to irreparable damage and void of warranty.

            • After the lock is installed, please change the default management pin code immediately and keep a record of your new code.

            • Keep the backup mechanical keys in a safe secure location which can be conveniently accessed if required.

            • A low voltage alarm will sound when the 4 x AA batteries need replacing.

            • Make sure the batteries are in the correct positive/negative terminals. Incorrect positioning of the batteries may short circuit and permanently damage the lock.

            • Please read the manual carefully before use, and operate the lock according to instructions.

            • User data will be retained if batteries are temporarily removed.

            • Low voltage warning will sound after each 'unlock' if battery voltage is below 4.8V.

            • Disclaimer: Figures and characters in this manual are for manual demonstration and may not reflect the exact type or style of each model. We reserve the right to display any product that best demonstrates the manual content.


            Activation to the lock via the mobile app must be completed to secure the lock.

            Initial Setup 

            Handle Orientation

            Handle Orientation Figure 01


            Determine your door opening direction from the image provided
            Use this direction to set the handle orientation the lock.











            Left Handle Figure 02

            Right Handle Figure 03


            Reverse Handle Direction  

            • To reverse the handle direction, you DO NOT need to unscrew the lock.

            • You can reverse the handles by shifting the tab downwards by using a small key (screw driver).

            • Fully unscrewing the lock may void warranty.






             Rear Handle Figure 04 

            Front Handle Figure 05


             Square Spindle Assembly 

            1. Assemble the square spindle in the front handle and fix it with the split pin provided.

            2. Ensure the arrow symbol on the clutch piece is point UP or DOWN

            3. If you do not assemble the spindle and install the lock on the door. You may need to damage the lock or door for entry. Incorrect installation is not covered by warranty.


            IMPORTANT: Ensure the arrow symbol is facing vertically for 'right' or 'left' handle direction, respectively. If installed incorrectly, you might need to damage the lock for entry.


             Lock Hardware Installation 

            Do not use a high torque electric drill or over tighten the fixing screws - This may damage the lock and void the warranty

             Drilling Instructions

            1. Ensure the drill holes are perpendicular to the door.
            2. check the dimensions physically incase the template is not to scale. 
            3. Incorrect backset alignment may damage to the locks function and durability.
            1. Using In the drilling template provided mark the holes
            2. Drill or Utilise the existing 1 x 54 mm hole which is the standard cutting for a regular handle lockset.
            3. Drill  the 1 x 30mm hole above the 54 mm hole from both sides to avoid damaging the door.
            4. Mark out and chisel a recess for the tubular latch finishing plate.
            5. Mark out and chisel the striker plate on the door frame. 

            Standard Lock Hardware Installation

            1. Loosely install the tubular latch
            2. Fit the front handle and install the square spindle with the provided split pin. Ensure the square spindle is aligned with the square clutch in the tubular latch
            3. Pulling the wire through the hole in the rear fixing plate
            4. Screw the 3 screws into the rear fixing plate
            5. Plug in the wire to the rear handle and bunch the cable into the rear handle keeping the wire away from moving parts
            6. Fix the rear handle to the rear fixing plate
            7. Insert batteries and test lock function with mechanical keys and card/code
            8. Rotate front and rear handles to check the smoothness of the handle to ensure the entire system is not over tightened.

            Fire Rated Lock Hardware Installation


            Fire Rating Compliance
            1. If you are installing this lock on a fire rated door, a separate fire rating kit is required for compliance. 
            2. Rubber Gaskets must be removed from the lock at installation 
            1. Loosely install the tubular latch
            2. Insert the fire rated seals in the holes
            3. Larger piece in the 30mm hole
            4. Smaller pieces ( x 2) in 54 mm hole, above and below the tubular latch
            5. Remove the rubber gasket seals from the locks bodies.
            6. Fit the front handle and install the square spindle with the provided split pin. Ensure the square spindle is aligned with the square clutch in the tubular latch
            7. Pulling the wire through the hole in the rear fixing plate
            8. Screw the 3 screws into the rear fixing plate
            9. Plug in the wire to the rear handle and bunch the cable into the rear handle keeping the wire away from moving parts
            10. Fix the rear handle to the rear fixing plate
            11. Insert batteries and test lock function with mechanical keys and card/code
            12. Rotate front and rear handles to check the smoothness of the handle to ensure the entire system is not over tightened.

            Fire Rated Seal Locations



            Mechanical Key Override 

            Flick the black cap covering the mechanical barrel on the front handle open

            The key cover is attached to the handle. Do not snap the black cap off.
            1. Insert the mechanical key. Turn it 90 degrees. This will retract the door latch.
            2. If the mechanical key does not turn, it is the wrong key.
            3. Try turning the key and handle at the same time to avoid breaking the mechanical key inside the cylinder.

             

                           


            Keep the mechanical back up keys in a safe and secure location in case of an emergency

            External Backup power Supply (USB-B)

            If the batteries are depleted, plug a battery pack/charger into the terminal on the base of the front handle. This will temporarily power the lock and will not recharge the batteries. 

            Troubleshooting

            If you experiencing any of the following faults, please check this quick guide. For further support please contact KAS


            Electronic/System Malfunction

            1. Try Power cycle by removing and replacing the batteries. Try a new set of batteries. Electronic components work best with a new set of batteries and a power cycle.

            Latch Not Retracting

            1. Check the spindle assembly and arrow direction
            2. Listen for a motor sound. If no, the motor has failed and will need a replacement. If yes, use mechanical key for access.

            No Power

            1. Check the batteries are inserted correctly.
            2. Ensure the cables are connected securely to the connections

            Drilling Dimensions





            Updated: 16 Jun 2019 04:23 PM
            Helpful?  
            Help us to make this article better
            0 0