Platinum Locks (LMS) - How to Program

Platinum Locks (LMS) - How to Program

Step # 1:

By default, the lock is permanently in an unlocked (“open”) state. This is factory default, which means the installer can never lock himself/herself out whilst installing. To put the lock in a normal auto-locking state (“only open when card present”) you can place a key card to the lock and that will initialize the lock.

Step # 2:

Insert batteries into the cartridge. Careful not to lose the screw, or tighten too tight – otherwise you can damage the plastic battery cartridge.

Step # 3:

Take mobile programmer and download software data before setting room number on the lock.

  1. Plug programmer into USB port (Note GEN 1: USB-encoder)
  2. Open software
  3. Click “download data”
  4. Wait for confirmation message

Make sure the mobile programmer has the most update to date ‘download data’ in the software.  This is the data logic that is transferred between the key cards and software setup and if incorrect, the lock will not function correctly. Any changes to a door in the ‘download data’ in the software will require door re-programming.  The software is setup remotely by KAS during client software install.

Step # 4:

Now you can program the locks with the mobile programmer.  Take the mobile programmer and do the following:

  1. Press ‘3’,
  2. Press ‘Run’,
  3. Enter ‘Programming Reference Number’
  4. Press ‘Run’,
  5. Hold to lock induction area,
  6. Wait until you see a confirmation message, *Repeat step if this confirmation message is not displayed on the Mobile Programmer. Try holding the Mobile Programmer about 5-10 cm away from lock face and move back and forth to strength the IR signal.
  7. Rotate privacy snib 90 degrees back and forth to confirm,
  8. One long beep heard for confirmation,

Programming Reference Number for example: 100317, i.e Building “10”, Floor “03”, Room “17”. This can be found on the ‘Set Room Number’ on the software or on a pre-filled Programming Reference Number Sheet which KAS fills out for every software setup installation after discussing with the clients.

PLEASE NOTE: If you have a GEN1 Mobile programmer, instead of pressing '3' then 'Run'. Press 'Func' 3 times then 'Run'.

Step # 5:

Set the clock; Note: It is possible to do this with the door closed.

  1. Press ‘1’,
  2. Press ‘Run’,
  3. Hold until programmer to lock induction area
  4. Wait until you see confirmation message, *Repeat step if this confirmation message is not displayed on mobile programmer
  5. One long beep is heard for confirmation

PLEASE NOTE: If you have a GEN1 Mobile programmer, instead of pressing '1' then 'Run'. Press 'Func' 1 time then 'Run'.

Step # 6:

Finally, present any key card on the lock reader and open the door. This will initialize the lock into an “auto-locking” state and test the RFID reader, electronics and locking function before moving onto the next door.

Things to check;

  • 1. Door handles functions correctly (both sides)
  • 2. Test with master key card for correct programming
  • 3. If the clock is not set, the guest room key cards will not work (as they are limited by time)

Lock programming complete.

If you do not have Access Control Readers installed,
Your system is ready.

Mobile Programmer model differences

  • GEN1 Mobile Programmer: Top row of buttons are "RUN" and "FUNC"
  • GEN2 Mobile Programmer: Top row of buttons are " RUN" and "CLR"

VIDEO





    • Related Articles

    • LMS Software - User Manual

      Full User Manual and Quick Reference Guide

    • Platinum Lock - Fire Certificates

      Platinum Lock hold the following fire certificates.  KAS recommends you speak to your certifier and supplying them with the relevant certificates before purchasing any hardware  Ecore: Mortise Latch & Tubular Latch Firecore: Mortise Latch & Tubular ...

    • LMS Access Control System - Installation Guide

      To setup and program the access control reader ​ There are 2 main components of the Access Control System (ACS) which you some become familiar with.  There are also additional optional devices that comprise the ACS, a door release and the REX button. ...

    • LMS Software - Installation Setup

      Please Click Here to download and install KAS LMS software If you are Reinstalling the software please backup your database first  After Installing the LMS software, copy the KAS-LMS (patch) file from the above link and paste into the lock software's ...

    • Platinum Lock - Drilling Template

      Platinum Drilling Template Speeds up installation time by 50-80%! Suitable for tubular latch or mortise latch 70mm backset only Wraps around the door and clamped in place to easily and quickly mark the drill holes Use the notches on the side to align ...